Click to Close
Click to Close

Bendpak PCL-18B- 2 Low Voltage 36,000 Lb. Mobile Lift System/208-230/190v,50-60HZ,3-Ph./SET OF 2

Free Shipping
SKU/Product #:

$ 15,760.00 

$ 0.00 

Call To Order

This PCL-18B mobile column lift system comes in a set of 2. When combined, the system lifts up to 36,000 lbs. A set of 2 is the perfect way to expand your lifting capabilities on vehicles with three or four axles. Sets of 4, 6 and 8 are available. Set of 2 Mobile Column Lifts With a pair (2) of mobile column lifts, you can add to your existing fleet and expand your lifting capabilities to include larger semi-trucks and heavy-duty vehicles. A minimum of 4 mobile column lifts must be used to lift a vehicle, and heavier vehicles require 6 or 8. This 2-set is a great way to gradually upgrade into the 6 or 8-lift range, offering up to 144,000 lbs. with a full set. Do not attempt to lift half of a vehicle (the front or back only) with only 2 mobile lifts. Vehicles must be raised on an even plane at all times.   Features 18,000-lb. individual column capacity / 108,000-lb. maximum system capacity Meets or exceeds the standards prescribed by ANSI/ALI ALCTV-2011 Two, four, or six column configurations can accommodate heavy duty trucks and light duty passenger vehicles 208-240V, 3-phase main power system - optional voltages available upon request SINGLE, PAIR or TEAM operation For a standard four-column set, just three 30' cables are used leaving the front or back of the lift clear of cable obstructions Simple operation, long service life and minimum maintenance Intuitive controls allow the lift to be fully programmed and controlled from any column Control systems feature 24-volt safety circuitry The PLC and main system components are standard off-the-shelf brands rather than proprietary printed circuit boards or controls, which can be very expensive to service or replace Smart electronics feature self-diagnostics and self-calibration functions Sealed and enclosed linear potentiometers feature precision potentiometric output and high-frequency response for precise synchronization and communication of all columns throughout all operation cycles for precise, level lifting Variable height limit settings can be programmed for shops with low ceilings or when specific vehicle service requirements necessitate specific rise heights Two-speed lowering option – turtle or rabbit speed settings Each column is equipped with a warning light and audible alarm for critical warning alerts Emergency shut-off switches on each column quickly shut off power to the lift in the event an unsafe condition is detected by the operator Separate key lock enclosure on each column Electronics are multi-fuse protected An enclosed electric-hydraulic power system that ensures quieter operation is better suited for sound-sensitive areas Pallet-jack style steering wheels enable the columns to be lowered firmly on the floor vs. constantly loaded spring-type steering wheels that can cause columns to roll when unladen by the weight of a vehicle Low-mounted power units and cylinders means a lower center of gravity, making the columns easier to move and less likely to topple vs. screw-drive systems with heavy overhead motors and drive systems Extended forks accommodate wide tires and deep wheel configurations Multi-width wheel forks with locking pins accommodate the widest range of wheels, eliminating the need for specialty wheel adapters Tandem 8” diameter polyurethane covered steel wheels with sealed roller bearings easily roll over dirt and debris Heavy-duty steel carriage rollers feature turned, ground and polished axle pins Manual safety override valves on each column permit the lift to be lowered in the event of a power outage without the need for manual hand cranks Durable forklift pockets provide simplistic handling when moving the lift columns from one facility to another Inverted hydraulic cylinders feature an integrated safety valve to prevent accidental uncontrolled lowering in the event of oil pressure loss Multiple, automatic, independent safety locks spaced every four inches ensure safe operation Space-saving design, reduced column weight and a tight turning radius provides improved mobility Use the lift to place vehicles on tall jack stands then use the columns to raise another vehicle in an adjoining bay Durable powder coat finish       

Lifting Capacity 18,000 lbs. (8,165 kg)  

A - Overall Height (RAISED) 101” (2,565 mm)  

B - Overall Height (LOWERED) 146.5” (3,721 mm)  

C - Max. Lifting Height 71.5” (1,889 mm)  

D - Overall Depth 48.75” (1,238 mm)  

E - Overall Width 45” (1,143 mm)  

F - Chassis Length 32.25” (819 mm)  

G - Min. Lifting Fork Width 9.5” (241 mm)  

H - Max. Lifting Fork Width 35” (889 mm)  

I - Lifting Fork Length 11.5” (292 mm)  

Turning Circle 40” (1,016 mm)  

Column Weight 1,450 lbs. (657 kg)  

Lifting Speed 85 sec  

Shipping Weight 1,450 lbs. (657 kg)   //   

For Questions

Bendpak PCL-18B- 2 Low Voltage 36,000 Lb. Mobile Lift System/208-230/190v,50-60HZ,3-Ph./SET OF 2
Talk to Our Equipment Experts